中央供料系統（集中供料系統）稱重式混料機，吸料機，吸粉機，真空上料機，氣力輸送機，真空加料機，中央供料系統廠家,提供注塑機中央供料系統、塑料中央供料系統、自動供料系統、注塑機集中供料系統，模溫機(壓鑄模溫機），工業冷水機，色母機，塑料粉碎機，高速脫油機，塑料干燥機，三機一體除濕機（塑料除濕干燥機），真空輸送機，輸送稱重系統，金屬分離器，。
產品中心
PRODUCT CENTER
- 聯系人 : 曹鏡森先生
- 聯系電話 : 0769-82226193
- 傳真 : 0769-82226193
- 移動電話 : 13925217478
- 地址 : ** 廣東省東莞市大朗鎮仙村工業區
- Email : caojingshen@126.com
- 郵編 : 523792
- 公司網址 : http://m.gameslessordinary.com
- MSN : caoshingcer@126.com
- QQ : 454992321
文章詳情
瓶胚高速注塑干燥系統
日期：2026-02-01 01:22
瀏覽次數：6
摘要：瓶胚高速注塑干燥系統,PET干燥系統,PET瓶胚.72腔瓶胚
瓶胚高速注塑干燥系統,PET干燥系統,PET瓶胚.72腔瓶胚
瓶胚高速注塑干燥系統 中英文雙語同步介紹
瓶胚高速注塑干燥系統是專為 PET 瓶胚高速注塑生產線設計的集成化聚酯干燥專用系統，是保障高腔數、高射速瓶胚注塑的核心前道工藝設備。
The drying system for high-speed preform injection moulding is an integrated special polyester drying system designed exclusively for high-speed PET preform injection production lines, and is the core front-end process equipment to ensure high-cavity, high-injection-speed preform injection moulding.
該系統以預結晶 + 深度低露點除濕干燥為核心，將 PET 切片含水率精準降至 20ppm 以下的瓶胚注塑**值，徹底避免高溫注塑時的 PET 水解降解，同時適配高速注塑的連續化、高節拍、無間斷供料要求。
With pre-crystallization + deep low dew point dehumidification drying as the core, the system accurately reduces the moisture content of PET chips to below 20ppm, the safe value for preform injection moulding, completely avoids PET hydrolysis and degradation during high-temperature injection moulding, and at the same time meets the requirements of continuous, high-cycle, uninterrupted feeding for high-speed injection moulding.
系統針對瓶胚高速注塑（32/48/96/144/288/320 腔，單模周期 3~5s）的工藝特性做專項設計，相比常規 PET 干燥系統，具備集成化程度高、控溫露點精準、密閉防吸濕、與注塑機聯動性強等特點，是食品、飲料、醫藥級 PET 瓶胚量產的必備核心系統。
Designed specifically for the process characteristics of high-speed preform injection moulding (32/48/96/144/288/320 cavities, single mould cycle 3~5s), the system has the characteristics of high integration, precise temperature and dew point control, airtight moisture-proof, and strong interconnection with injection moulding machines compared with conventional PET drying systems, and is an essential core system for mass production of food, beverage and pharmaceutical grade PET preforms.
一、系統應用核心必要性
瓶胚高速注塑對 PET 切片的干燥品質要求遠高于常規 PET 加工，高腔數、高射速的工藝特性會將干燥不達標帶來的問題無限放大，直接決定瓶胚成型品質與生產線效率。
High-speed preform injection moulding has much higher requirements for the drying quality of PET chips than conventional PET processing, and the process characteristics of high cavity number and high injection speed will infinitely amplify the problems caused by substandard drying, which directly determines the preform forming quality and production line efficiency.
PET 為強吸濕性材料，若切片含水率＞20ppm，高溫注塑時會發生劇烈水解，導致瓶胚出現發白、霧斑、氣泡、縮痕等外觀缺陷，力學性能大幅下降，后續吹瓶易破裂、壁厚不均。
PET is a highly hygroscopic material; if the moisture content of the chips is ＞20ppm, severe hydrolysis will occur during high-temperature injection moulding, leading to appearance defects such as whitening, foggy spots, bubbles and shrinkage marks on the preforms, a sharp drop in mechanical properties, and easy cracking and uneven wall thickness in subsequent bottle blowing.
瓶胚高速注塑生產線為連續化運行，單模周期僅 3~5s，若干燥系統供料中斷、切片干燥不均，會導致整線停機，288 腔生產線每停機 1 分鐘即損失超 2000 個瓶胚，產能損耗巨大。
The high-speed preform injection production line runs continuously with a single mould cycle of only 3~5s. If the feeding of the drying system is interrupted or the chip drying is uneven, the entire line will stop. A 288-cavity production line loses more than 2000 preforms per minute of downtime, resulting in huge capacity loss.
常規 PET 干燥系統存在集成化低、露點波動大、易二次吸濕等問題，無法適配高速注塑的精準控溫、連續供料、低露點穩定要求，而專用的瓶胚高速注塑干燥系統為工藝量身設計，從根源上解決干燥痛點。
Conventional PET drying systems have problems such as low integration, large dew point fluctuations, and easy secondary moisture absorption, which cannot meet the requirements of precise temperature control, continuous feeding, and stable low dew point for high-speed injection moulding, while the special drying system for high-speed preform injection moulding is tailor-made for the process and solves the drying pain points from the root cause.
干燥系統與瓶胚注塑機、模具除露機共同構成瓶胚高速注塑的核心工藝鏈，干燥品質決定瓶胚基礎成型質量，是后續除露、成型、脫模等環節的工藝基礎。
The drying system, together with the preform injection moulding machine and mould dehumidifier, forms the core process chain of high-speed preform injection moulding. The drying quality determines the basic forming quality of the preform and is the process basis for subsequent links such as dehumidification, forming and demoulding.
